Log in...

Active holder for fixed installation

Adjustable holder. Fits devices with skin original case/skin. With tilt swivel. 2A charging. 12/24V

Keep your phone's battery fully charged in an active holder, always within easy sight and reach! Neat, discreet and convenient. For fixed installation. The holder is to be connected inside the dashboard, providing an elegant installation without any cables hanging over the interior. You have full access to the camera and all buttons when the device is in the holder. It is easy to slide the phone in place in the holder so it connects to the charging, and to take it out of the holder when leaving the vehicle.

 

The holder is equipped with a tilt swivel so you can easily adjust the angle for better viewing, or switch between portrait and landscape mode. Tilts 20° and swivels 360°. Mounting plate 42x50 mm with AMPS-holes. Made of high grade black ABS/Acetal plastic. Made in Sweden. Connect the power cable with a 2A fuse. Professional installation recommended. Attach onto ProClip Mounting Platform.

Charging specification:

Cable length: Total length: 338 cm (Holder to box: 170 cm, Connectors+box 14 cm, Box to open end: 154 cm.)

 

Charging specifications:

Input voltage: DC/10-30V

Charging voltage: DC/4.75-5.3V

Output current(Typ): 2.0A

Input & output protection: Input polarity reversal/Output over voltage/Output over current/Output short protection

LED charging indicator: Power input indicator(Green), Ovp/Ocp/Output short(Red)

Operating temperature: 0°C ~ +40°C

Storage temperature: -20°C ~ +80°C

Approvals: E, CE, FCC, ROHS.

  • Item no: 713063
  • EAN: 7320287130638

  • Width: 83 mm
  • Height: 91 mm
  • Depth: 55 mm
  • Volume: 415 cm³
  • Weight: 204 g

Item no 713063 fits:

  • OnePlus 6 (For all countries)
  • OnePlus 6T (For all countries)
  • OnePlus 7 (For all countries)
INSTALLATION INSTRUCTIONS:

1.

2.

3.

4.

Read all of the instructions before attaching the holder. Important Note: Connect to a 2 A fuse holder and fuse inline with the Red wire close to the power source. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area! Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle. How to mount the holder: 1. To adjust the holder for your device: Loosen the screws on the front side of the holder, so the sides of the holders can be adjusted. 2. Place the device in the holder and press the sides together so the device is firmly in place. Adjust the positioning of the charging connector so it connects properly to the phone. Lock the charging connector into position by screwing the screw into the hole on the side of the charging connector block. Remove the device carefully. Tighten the screws on the front side of the holder. 3. To install the holder: Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Screw a few turns on the screw, just so the thread starts to pull. Pull the holder toward you and hold it slightly tensed, in the same time tighten the screw so the holder is pulled toward the tilt swivel. Tighten the screw firm at first, then loosen it a bit so the holder is firmly in place, but still can be adjusted. 4. The holder is in place.

Attach your holder onto a ProClip!

You need two parts; a ProClip for your car, and a holder for your device. Find the correct ProClip for your vehicle here: