Log in...

Mount

Rail mount for OtterBox uniVERSE case. With USB-cable + cig-plug adapter with 2 USB ports: QC 3.0A + 2.4A. With tilt swivel. 12/24 Volt. Charging via pogo pins. With easy-switch system.

Keep your phone's battery fully charged in an active holder, always within easy sight and reach! Neat, discreet and convenient. Custom made with a perfect, firm fit for OtterBox uniVERSE case. Simply snap/slide your phone into place on the rail mount for easy attachment and charging connection. With USB-cable with cig-plug adapter, choose to connect either to the vehicle's USB outlet or the 12/24V socket. The cig-plug adapter has two USB ports: QC 3.0A + 2.4A. You have full access to all buttons when the device is in the holder.

 

The holder is equipped with a tilt swivel so you can easily adjust the angle for better viewing, or switch between portrait and landscape mode. Tilts 17° and swivels 360°. Mounting plate 42x50 mm with 4 mm AMPS-holes. Made of high grade black ABS/Acetal plastic. Made in Sweden. Color: black. Attach onto a ProClip mounting platform.

 

Easy-switching system:

The easy-switching system enables you to upgrade the holder only, and keep the installed cables. It saves you a lot of time! When upgrading to a new device, you do not longer need to make a full installation. Same goes for maintenance in case of warranty or damage. You simply disconnect the holder from the charging cable via the Molex 6-pin quick connector, and then connect the new holder. The switch is done in a few seconds.

 

Important note!

In order to be able to transmit audio files from your device through the USB-cable, this feature must be supported by the stereo in your car. You can easily test if this works by connecting your device to the stereo with the USB/charging cable that comes with your device. Charging through USB works regardless.

Charging specification:

- Output Connector Type: Dual USB Type-A Female.

- Output Voltage: 5V, 9V, 12V(Nominal)

- Output Current:
- USB Port 1: 4.9V ~ 5.25V 2.4A (White port, recommended for Apple)
- USB Port 2: 3.6V ~ 6V/3A 6.2-9V/2A 9.2-12V/1.5A (Green port, recommended for Android etc)
- Output Voltage Ripple: 300mV pk-pk at Max Load

- Input Voltage Range: DC 12--24V DC, Input can handle 40V Load dump translent events

- Input Current: 3.0 A DC Max

- Input Current with No device attached: 0.005A

- DC-DC Conversion Efficiency: Over 86% Typical

- Rated Power:

- USB Port 1: 12 Watts Max. White port.

- USB Port 2: 18 Watts Max. Green port.

 

  • Item no: 721216
  • EAN: 7320287212167

  • Width: 53 mm
  • Height: 136 mm
  • Depth: 50 mm
  • Volume: 360 cm³
  • Weight: 200 g

Item no 721216 fits:

  • Samsung Galaxy Xcover Pro SM-G715 (For all countries)
INSTALLATION INSTRUCTIONS:

1.

2.

3.

4.

Please read all of the instructions and look at the pictures before attaching the mount.  
   
1. Loosen the screw in the center of the mount so you can remove the tilt swivel attaching plate on the back.  
   
2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws.  
   
3. Place the mount over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the holder is firmly in place, but still can be adjusted.  
   
4. The mount is in place.