Log in...

Active holder with cig-plug

With USB-cable + cig-plug adapter with 2 USB ports: QC 3.0A + 2.4A. With tilt swivel. 12/24 Volt.

Keep your battery fully charged in an active holder, always within easy sight and reach! Neat, discreet and convenient. Custom made with a perfect, firm fit. With USB-cable with cig-plug adapter, choose to connect either to the vehicle's USB outlet or the 12/24V socket. The cig-plug adapter has two USB ports: QC 3.0A + 2.4A. It is easy to slide the device into place in the holder so it connects to the charging, and to take it out of the holder when leaving the car.

 

The holder is equipped with a tilt swivel so you can easily adjust the angle for better viewing. Tilts 17° and swivels 360°. Mounting plate 42x50 mm with 4 mm AMPS-holes. Made of high grade black ABS/Acetal plastic. Made in Sweden.

 

Tablets (Surfpads) should not be installed onto a car’s dashboard if they block the view or block key controls. ProClip (Brodit’s vehicle mounting bracket) is designed for installation of smaller devices like mobile phones and GPS devices, ProClip is not designed for large devices like tablets. In some vehicles the ProClip has an extra firm fit and can then be used also for installation of a tablet. If you want to place a tablet onto the car’s dashboard, each combination of tablet-car must be examined in detail by you in order to determine if such an installation is possible in the specific case. Consideration should be given to the position and how firmly the ProClip is in place, as well as the size of the tablet you wish to use. Brodit will not give any recommendations for such installations.

 

An installation of a tablet onto a vehicle’s dashboard is always done on the customer’s own responsibility. Brodit recommends to use tablets on the car’s headrest, installed onto a Brodit headrest mount.

 

Charging specification:

- Output Connector Type: Dual USB Type-A Female.

- Output Voltage: 5V, 9V, 12V(Nominal)

- Output Current:
- USB Port 1: 4.9V ~ 5.25V 2.4A (White port, recommended for Apple)
- USB Port 2: 3.6V ~ 6V/3A 6.2-9V/2A 9.2-12V/1.5A (Green port, recommended for Android etc)
- Output Voltage Ripple: 300mV pk-pk at Max Load

- Input Voltage Range: DC 12--24V DC, Input can handle 40V Load dump translent events

- Input Current: 3.0 A DC Max

- Input Current with No device attached: 0.005A

- DC-DC Conversion Efficiency: Over 86% Typical

- Rated Power:

- USB Port 1: 12 Watts Max. White port.

- USB Port 2: 18 Watts Max. Green port.

  • Item no: 721255
  • EAN: 7320287212556

  • Width: 199 mm
  • Height: 142 mm
  • Depth: 42 mm
  • Volume: 1187 cm³
  • Weight: 280 g

Item no 721255 fits:

  • Lenovo Tab M8 HD TB-8505X (Micro-USB) (For all countries)
INSTALLATION INSTRUCTIONS:

1.

2.

3.

4.

Please read all of the instructions and  look at the pictures before attaching the holder.
 
1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back.

2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the holder is firmly in place, but still can be adjusted.
 
3. To place the device in the holder: Slide the device sideways into the holder until you hear / feel it snaps into place. To remove the device from the holder: Slide the device sideways and out.
 
4. The holder is in place.

Attach your holder onto a ProClip!

You need two parts; a ProClip for your car, and a holder for your device. Find the correct ProClip for your vehicle here: