Log in...

Active holder for fixed installation

With tilt swivel. Fits for devices with skin; adjustable top.

Use an active holder for your device on the road and you will always have a freshly charged battery! In addition, you will always have your device within easy sight and reach. Safe, comfortable and convenient! For fixed installation. The holder is to be connected inside the dashboard, providing an elegant installation without any cables hanging over the interior. The charging box has two USB ports: QC 3.0A + 2.4A. You have full access to the camera and all buttons when the device is in the holder. Fits devices with skin. The top part of the holder is adjustable and adapts to the height of your phone.
   
The holder has a perfect fit. It is easy to put the device into the holder, and just as easy to take it with you when leaving the vehicle. The holder is equipped with a tilt swivel so you can adjust the angle of your device in order to avoid light reflection on the screen. You can tilt the holder 17° in each direction. Attach onto ProClip Mounting Platform.

 

Important note!

For Samsung Galaxy Note 20 Ultra 5G can you have problem with some settings in the camera.

Charging specification:

- Input Molex 2-Pin

- Output Connector Type: Dual USB Type-A Female.

- Output Voltage: 5V, 9V, 12V(Nominal)

- Output Current:
- USB Port 1: 3.6V ~ 6V/3A 6.2-9V/2A 9.2-12V/1.5A (Recommended for Android etc)
- USB Port 2: 4.9V ~ 5.25V 2.4A (Recommended for Apple)
- Output Voltage Ripple: 300mV pk-pk at Max Load

- Input Voltage Range: DC 12--24V DC, Input can handle 40V Load dump translent events

- Input Current: 3.0 A DC Max

- Input Current with No device attached: 0.005A

- DC-DC Conversion Efficiency: Over 86% Typical

- Rated Power:

- USB Port 1: 18 Watts Max.

- USB Port 2: 12 Watts Max.

  • Item no: 727218
  • EAN: 7320287272185

  • Width: 58 mm
  • Height: 189 mm
  • Depth: 49 mm
  • Volume: 537 cm³
  • Weight: 205 g

Item no 727218 fits:

  • Samsung Galaxy Note 20 Ultra 5G (For all countries)
  • Samsung Galaxy S20 Ultra 5G (For all countries)
INSTALLATION INSTRUCTIONS:

1.

2.

3.

4.

Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Note: If you are connecting a GPS/Data device to the holder please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters. Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle. Attaching the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the holder is firmly in place, but still can be adjusted. 3. To place the device in the holder: Place the upper part of the device in the holder, then press the device forwards and upwards so it snaps into place in the holder. To remove the device from the holder: Press upwards on the lower part of the device, in the same time pull the the device out and down from the holder. 4. The holder is in place.

Attach your holder onto a ProClip!

You need two parts; a ProClip for your car, and a holder for your device. Find the correct ProClip for your vehicle here: